The Hidden Challenges of Scaling Medical Device Production
Why product design, assembly, and manufacturing strategy matter when a medical device moves from small builds to high-volume production.

A product can look great on paper, work exactly as intended as a prototype, and assemble without much trouble in small quantities. But ask a manufacturing team to build that same product thousands of times, and a different set of questions starts to surface.
How many steps does it take to assemble? How long does each step take? Do the parts go together easily, or does every unit need a careful adjustment? What needs to be inspected, and how do we know each unit was built correctly?
These questions matter most for disposable medical devices. Tubing assemblies, connectors, fluid management components, and other single-use products often must hit competitive price points while meeting strict functional and quality requirements. Across thousands or millions of units, even a small increase in material, assembly time, or inspection can noticeably change the cost of each device.
This is where product design and manufacturing strategy meet. The decisions made during development shape how a device performs, along with how efficiently it can be made throughout its production life.
Every part costs more than its price
One of the basic principles of product design is to avoid unnecessary complexity. It sounds obvious, but it is worth looking at what one extra component brings into a manufacturing process.
Consider a disposable fluid-path assembly made up of a molded connector, tubing, a seal, and a protective cap. Each component has a purpose. Each one also must be made or sourced, handled, positioned, and assembled. Depending on the design, it may also need to be bonded, secured, or inspected.
Now add one smaller component. Its purchase price might be negligible. But it may also bring another supplier, another incoming inspection, another assembly step, and another point to verify during production.
The cost is no longer just the price of the part.
This is one reason Design for Manufacturing and Assembly (DFMA) puts so much weight on reducing part count. Fewer components can mean less handling, fewer assembly operations, simpler inventory, and fewer chances for assembly errors.
There is an important distinction, though. Fewer parts do not automatically mean a cheaper product. Combining two components into a single molded part might cut assembly time, but it could also require more complex tooling or a more expensive process.
The real question is whether the complete product can be made and assembled at a lower overall cost without compromising its function.
Design parts that go together easily
A component can be easy to manufacture and still be surprisingly difficult to assemble. That distinction is easy to miss when most early design work focuses on individual parts.
Take a small, molded connector that must be inserted into a housing. If the mating geometry offers little to no guidance, the operator must carefully position and align the connector before it can be secured. The step may only take a few seconds, but it demands attention and can vary from one operator to the next.
A small design change, such as a lead-in chamfer, a locating feature, or geometry that guides the parts into alignment, can make the same step much easier.
The same thinking applies across disposable device assemblies:
• Make parts self-locating. Use features that guide components into position rather than relying on manual alignment.
• Avoid unnecessary adjustments. Any step that asks an operator to judge, position, or fine tune a part adds time and variation.
• Make orientation obvious. Where possible, make parts symmetrical so orientation does not matter. Where it does matter, make the asymmetry easy to see.
• Provide access and visibility. Operators, assembly tools, and inspection equipment all need to reach the features they work on.
• Think about parts in bulk. A part that is easy to pick up on its own may tangle, nest, or be hard to orient when hundreds of them arrive in a bin.
None of these ideas are complicated, but they make a considerable difference when repeated across a large production run. Good design makes the correct way to assemble a device the easiest way. Parts should fit together naturally, need minimal handling, and make it clear when they have been assembled correctly.
A few seconds add up
Production volume changes how an assembly step should be judged.
For a small batch, positioning and joining parts by hand is often perfectly practical. There is little reason to invest in specialized equipment when an operator can do the job at a simple workstation with basic tools.
But what happens when production increases?
Consider an assembly step that adds 10 seconds to each device. For a batch of 100 units, that is less than 17 minutes. It hardly seems worth noticing.
Across 100,000 units, those same 10 seconds add up to roughly 278 hours of production time, or nearly seven weeks of work for one full-time operator. That is for a single operation, before accounting for the rest of the assembly.
This is where manufacturing teams start looking for improvements. Could a fixture hold the parts in position? Could a dispensing system apply adhesive more consistently? Could a small change in part geometry remove a manual alignment step altogether?
Sometimes a simple fixture is all that is needed. In other cases, semi-automated equipment or a dedicated assembly station makes better economic sense. Each option comes with its own investment. Fixtures need to be designed and built, equipment needs to be set up, and the process needs to be evaluated before it can be relied on.
Volume changes the cost equation
No single manufacturing method makes sense at every production quantity.
At lower volumes, manual assembly offers flexibility and relatively low setup costs. Operators work at individual stations with basic tools and simple fixtures, and changes to the product or process are easy to accommodate.
As demand grows, the economics shift. Dedicated fixtures improve positioning and reduce handling. Specialized equipment shortens repetitive operations. At high enough volumes, robotic or dedicated automated assembly becomes worth considering.
Automation is not automatically the most economical choice, however. A dedicated automated system can require substantial upfront investment, take time to develop, and be difficult or expensive to modify if the product changes. For a product with uncertain demand or frequent design revisions, a more flexible approach may be the better choice.
The right answer depends on expected volume, labor, cycle time, product complexity, and the cost of setting up and maintaining the process. That is why production forecasts belong in early engineering discussions.
A process that works well for 500 units may not be the best choice for 50,000. Equally, investing in high-volume automation before demand justifies it adds cost that the product then has to carry.
Quality is part of the process, too
Assembly time is only part of the equation. Every operation also has to produce a consistent result.
Consider a tubing connection that must be inserted to a specified depth and bonded securely. If the insertion depth or bonding conditions vary, the connection may not perform as intended.
Manufacturers need to decide how operations like this will be controlled and verified. Depending on the product and process, that could mean positioning fixtures, defined process parameters, visual inspection, dimensional checks, or functional testing. Some checks happen during assembly. Others happen at the end of the line.
Some results cannot be fully checked afterward at all. The strength of a bonded joint, for example, often cannot be confirmed without destroying the part. ISO 13485, now incorporated into the FDA's Quality Management System Regulation (QMSR), requires processes like these to be validated, so that confidence comes from a controlled process rather than from inspection alone.
Every inspection or verification step takes time, resources, and sometimes specialized equipment. But removing checks simply to reduce cost is not the answer either. The process needs the right controls to show that the device meets its requirements.
This brings us back to product design. Can the component be made easier to position? Can the assembly give a clear sign that it is fully seated? Can a critical feature be inspected without taking the assembly apart? Can the process be designed so that an incorrect assembly is difficult to build in the first place?
The best process is not necessarily the one with the fewest inspection steps. It is the one that consistently produces the required result, with the right controls built into the operation.

Not every cost shows up in the unit price
When evaluating the cost of a medical device, it is easy to focus on the bill of materials. Connectors, tubing, molded components, and other purchased parts are visible and easy to compare. But there is more to a finished product.
Direct manufacturing costs include materials, purchased components, assembly labor, consumables, packaging, and per-unit testing. Indirect costs support the operation, such as equipment maintenance, utilities, facilities, production supervision, and quality management. Then there is the setup, or non-recurring, costs of preparing the process: tooling, mold development, fixture fabrication, equipment setup, process development, and initial validation.
Each of these needs to be looked at separately when evaluating a manufacturing quote. A dedicated fixture may be a significant upfront expense, but it can shorten assembly time for every unit that follows. A tooling investment may look large at the start but become economical once it is spread across a larger production quantity.
This is why the lowest quoted unit price does not always mean the lowest overall manufacturing cost. Order quantity, setup charges, tooling ownership, expected demand, and recurring production expenses all belong in the comparison.
A competitive cost structure comes from understanding the complete manufacturing process, not from negotiating a lower price on individual components.
Address manufacturing challenges before production
One of the more expensive situations in product development is discovering that a device is difficult to manufacture after its design and production process have already been established.
A connector that is difficult to align may need a redesigned fixture. A component with unnecessarily tight tolerances may drive up machining and inspection costs. An assembly with too many manual operations may need new component geometry or a different joining method.
Each of these changes can bring engineering time, new tooling, updated documentation, additional testing, and production delays. For a medical device, every change also must go through change control, with its own review, verification, and records.
In our previous post, we looked at Design for Manufacturing (DFM) and Design for Assembly (DFA) as ways to make a device perform consistently. They matter just as much for cost. DFM looks at how materials, geometry, tolerances, and manufacturing methods affect the cost and ease of producing each component. DFA focuses on simplifying assembly by removing unnecessary parts and making the remaining ones easier to handle, orient, insert, and secure.
Applying both during development lets manufacturing considerations shape the design while there is still room to change it. It also shows the value of bringing design engineers, manufacturing engineers, and quality teams into the same conversation early. A decision that looks minor from a functional point of view can have a much larger impact when it is repeated across an entire production run.
Not every manufacturing challenge can be predicted, and not every design revision can be avoided. But many unnecessary operations, difficult assembly interfaces, and avoidable costs can be identified before they become a permanent part of the production process.
Good manufacturing economics start with good engineering
Scaling a disposable medical device takes more than adding production capacity. It takes a careful balance between product performance, assembly efficiency, process control, and cost.
The number of components, the sequence of operations, the time each step takes, the fixtures and equipment involved, and the checks needed to maintain quality all add to the final manufacturing cost. A device that is inexpensive to prototype is not necessarily inexpensive to manufacture at scale. The difference often comes down to how thoughtfully the product, and its manufacturing process were developed together.
The most competitive manufacturing processes are not always the most automated, or the ones with the fewest components. They are the ones where the design, assembly method, production volume, and quality requirements have been considered together.
Ultimately, good engineering is about more than making a device work. It is about understanding how that device will be made, assembled, and inspected consistently, not just once, but thousands or millions of times, so that every unit that reaches a patient performs like the one before it.
Senior R&D Engineer




Comments