Inside a Medical Device: The Journey from PCB Design to Production
The first version of a control-board schematic I worked on for a medical device didn't look especially complicated. There was a microcontroller, two indicator LEDs and a switch. I could point to each part and explain what it was supposed to do.
Then I started adding everything the board needed around those parts.
The battery couldn't just be connected to every component. The processor needed a different voltage. The board also had to control hardware outside itself, and I needed to think about what would happen if something was connected incorrectly or stopped responding. A simple-looking schematic became a collection of separate circuits, each with its own questions.
That experience changed how I look at electronic medical equipment. When I see a patient monitor now, I don't only think about the reading on the screen. I wonder how that reading gets there and how the electronics are designed to handle things going wrong.
A pacemaker and a smartphone both contain carefully designed electronics, but we expect very different things from them. A phone that dies halfway through the day is annoying. A problem with a pacemaker could be much more serious. Pacemakers use specialized electronic assemblies, of course, but the comparison explains why the engineering behind medical devices deserves so much attention.
A big part of that engineering happens on a printed circuit board, usually called a PCB. It's the physical board that supports the components and connects them through copper pathways. Here's what it takes to get from an early circuit idea to an assembled board that a manufacturer can produce consistently.
Before drawing the circuit
I used to think component selection would be the natural starting point. Need a battery? Find one with the right voltage. Need a sensor? Choose one that can measure what you're interested in.
It doesn't work quite like that. Before selecting either, you need to know what the device actually requires.
Consider a battery-powered medical instrument. What does it need to do when the charge is low? How much current will the electronics draw when everything operates at once? If a sensor is disconnected, should the device stop, alert the operator or continue in a reduced mode? The answers depend on the device and the risks involved.
This is why requirements and risk management come first. ISO 14971 is one of the standards used to structure medical device risk management. It doesn't design the circuit for you. It helps make sure foreseeable hazards and their controls aren't treated as an afterthought.
I find that a few clear requirements are worth more than a long list of components chosen too early.
A schematic is where you find the questions you missed
The schematic shows how components connect electrically. It can contain the power supply, processor, user controls and interfaces to other subsystems. On screen, they look like symbols linked by lines.
One area that took more thought than I'd expected was power. The incoming supply was suitable for some hardware, but not for the microcontroller. Adding voltage regulation solved one part of the problem. It raised several more. Was the regulator sized for the load? Did the input need reverse-polarity protection? What would happen during a sudden change in current demand?
I had similar questions when connecting the control board to external hardware. Drawing a wire is easy; confirming what voltage and signal that other device expects takes work. Sometimes the answer is in a datasheet. Sometimes you have to go back to a supplier and ask.
I also remember the satisfaction of getting an electrical-rules check to report no errors. That was progress, but it wasn't proof the design would work. A software check can flag certain connection problems. It can't establish that the entire circuit is suitable for its intended application.
That distinction has stayed with me. The schematic is an important record of the design, but the judgment behind it matters just as much.
Fitting the circuit into the real world
PCB layout turns the schematic into an actual arrangement of components and copper tracks, known as traces. Each part has a physical footprint. The connections have to fit between those footprints, sometimes across several copper layers.
A board isn't just a puzzle where the aim is to make every line connect. Sensitive signals can pick up noise from power circuits. Traces that carry substantial current need the right dimensions. Heat-producing components need room and an appropriate way to dissipate heat.
And the board has to fit inside something. A connector placed in the wrong spot might be electrically fine and practically unusable once the enclosure is assembled. This is where electrical design and mechanical design start influencing each other in very obvious ways.
For a medical device, layout decisions also need to reflect the operating environment and applicable safety and electromagnetic-compatibility requirements.
What the manufacturer actually makes
After layout, the designer sends manufacturing files to a PCB fabricator. Those files specify the board outline, holes and copper patterns. The fabricator checks whether the features can be manufactured within its process capabilities.
Many rigid PCBs start with fiberglass-reinforced epoxy and copper. The copper is patterned into conductive paths; holes are drilled and, where needed, plated to connect layers. A multilayer board is built by aligning and laminating its layers together.
The familiar green finish is normally solder mask, a coating that protects much of the copper. The small printed labels are called silkscreen. They help people identify components and connectors during assembly and troubleshooting.
At this stage the manufacturer has made a bare PCB. It still needs its electronic parts.
In assembly, solder paste is applied to the appropriate pads and machines place tiny components onto the board. A controlled heating process, called reflow soldering, forms many of the joints. Other parts can require different methods. Inspection follows, sometimes using X-rays for joints that can't be seen from the outside.
The assembled board is called a PCBA. It may look finished, but appearance says very little about whether it performs correctly.
The first working reading is only the beginning
I've spent time troubleshooting sensors on another medical electronics prototype. Getting numbers to appear in a terminal after working through code and connections felt like real progress. It was progress. But I had to separate two questions: was the device communicating, and was the sensor measuring what I thought it was measuring?
Those are not the same question. Sensor positioning, physical contact and electrical noise can change the values we see. A stream of plausible-looking numbers can still leave a lot unresolved.
The same principle applies when a new circuit board powers up. Engineers check voltages, signals, current draw and behavior under different operating conditions. Depending on the medical device, testing may include electrical safety, electromagnetic compatibility and temperature. Standards such as the IEC 60601 series can apply to medical electrical equipment.
There is also a distinction between verification and validation. Verification checks a design against its requirements. Validation addresses whether the finished device meets its intended use and user needs. A board that turns on is a good start, not the end of either process.
What changes when you need a hundred of them?
During prototype development, you can replace a part, change the wiring and try again. Production needs a different level of consistency. Components have to be available, assembly instructions have to be clear, and every unit needs appropriate inspection and testing.
Medical device quality systems, including those described by ISO 13485, help manage things such as design changes, supplier controls, records and traceability. The exact requirements depend on the device and the market.
People sometimes use the term medical-grade PCB as though it describes one special type of board. It doesn't. A board's suitability comes from the requirements of the finished device and the evidence that its design and manufacturing processes meet them. An electronic thermometer and an implantable cardiac device aren't going to need the same controls.
My own work has given me a much better appreciation for the decisions that happen before anyone gets to hold a finished product. It's not the copper or the components alone that interest me now. It's why they were chosen, what was checked, and what still needs to be proved.
Most people never see any of that when they use medical equipment. They see a device and expect it to do its job. The work that went into making that possible is largely hidden, which is exactly why I think it's worth talking about.
Ahaan Kareem
Junior Engineer

Our accelerated in house services include:
RD
Weekly Prototyping
Animations
Sensors
Wearables
App development
PCB design
LCD screens
Regulatory Services
PreSub / 513g regulatory work
Supplier Sourcing
User Testing
Usability Studies
Form Factor
UV laser etching
RF Welding
Ultrasonic Welding
Mold Flow Analysis
Hydrophilic and Hydrophobic Coatings
Balloon Development Manufacturing
Balloon symmetrical and A-symmetrical
Balloon layer development
Plastic Injection Molding <48”
Micro Plastic Injection Molding <1mm
Die Mold Tooling (Aluminum, Harden Steel, Copper, etc)
Die Mold Tooling Revisions
Packaging Labeling
Blister Tray Development Manufacturing
ETO Sterilization
2 pallet ETO Sterilization
Sterilization Validation
510k Submissions
Regulatory Testing
Marketing
Social Media
Merchant Services
Distribution and Warehousing
Website
Medical Sales Team




Comments